2015-10-16 11:04:50 +02:00
# ifndef PINS_H
# define PINS_H
/*
The board assignment defines the capabilities of the motherboard and the used pins .
Each board definition follows the following scheme :
CPU_ARCH
ARCH_AVR for AVR based boards
ARCH_ARM for all arm based boards
STEPPER_CURRENT_CONTROL
CURRENT_CONTROL_MANUAL 1 // mechanical poti, default if not defined
CURRENT_CONTROL_DIGIPOT 2 // Use a digipot like RAMBO does
CURRENT_CONTROL_LTC2600 3 // Use LTC2600 like Foltyn 3D Master
CURRENT_CONTROL_ALLIGATOR 4 //Use External DAC like Alligator
*/
# define ARCH_AVR 1
# define ARCH_ARM 2
# define CURRENT_CONTROL_MANUAL 1 // mechanical poti, default if not defined
# define CURRENT_CONTROL_DIGIPOT 2 // Use a digipot like RAMBO does
# define CURRENT_CONTROL_LTC2600 3 // Use LTC2600 like Foltyn 3D Master
# define CURRENT_CONTROL_ALLIGATOR 4 //Use External DAC like Alligator
# define CURRENT_CONTROL_MCP4728 5 // Use an i2c DAC as a digipot like PrintrBoard Rev. F
/****************************************************************************************
* Arduino pin assignment
*
* ATMega168
* + - \ / - +
* PC6 1 | | 28 PC5 ( AI 5 / D19 )
* ( D 0 ) PD0 2 | | 27 PC4 ( AI 4 / D18 )
* ( D 1 ) PD1 3 | | 26 PC3 ( AI 3 / D17 )
* ( D 2 ) PD2 4 | | 25 PC2 ( AI 2 / D16 )
* PWM + ( D 3 ) PD3 5 | | 24 PC1 ( AI 1 / D15 )
* ( D 4 ) PD4 6 | | 23 PC0 ( AI 0 / D14 )
* VCC 7 | | 22 GND
* GND 8 | | 21 AREF
* PB6 9 | | 20 AVCC
* PB7 10 | | 19 PB5 ( D 13 )
* PWM + ( D 5 ) PD5 11 | | 18 PB4 ( D 12 )
* PWM + ( D 6 ) PD6 12 | | 17 PB3 ( D 11 ) PWM
* ( D 7 ) PD7 13 | | 16 PB2 ( D 10 ) PWM
* ( D 8 ) PB0 14 | | 15 PB1 ( D 9 ) PWM
* + - - - - +
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 0
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega168__
# error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu.
# endif
# define ORIG_X_STEP_PIN 2
# define ORIG_X_DIR_PIN 3
# define ORIG_X_ENABLE_PIN -1
# define ORIG_X_MIN_PIN 4
# define ORIG_X_MAX_PIN 9
# define ORIG_Y_STEP_PIN 10
# define ORIG_Y_DIR_PIN 7
# define ORIG_Y_ENABLE_PIN -1
# define ORIG_Y_MIN_PIN 8
# define ORIG_Y_MAX_PIN 13
# define ORIG_Z_STEP_PIN 19
# define ORIG_Z_DIR_PIN 18
# define ORIG_Z_ENABLE_PIN 5
# define ORIG_Z_MIN_PIN 17
# define ORIG_Z_MAX_PIN 16
# define ORIG_E0_STEP_PIN 11
# define ORIG_E0_DIR_PIN 12
# define ORIG_E0_ENABLE_PIN -1
# define SDPOWER -1
# define SDSS -1
# define LED_PIN -1
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN 15
# define HEATER_0_PIN 6
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
# define TEMP_0_PIN 0
2015-10-16 11:04:50 +02:00
# endif
/****************************************************************************************
* Sanguino / RepRap Motherboard with direct - drive extruders
*
* ATMega644P
*
* + - - - \ / - - - +
* ( D 0 ) PB0 1 | | 40 PA0 ( AI 0 / D31 )
* ( D 1 ) PB1 2 | | 39 PA1 ( AI 1 / D30 )
* INT2 ( D 2 ) PB2 3 | | 38 PA2 ( AI 2 / D29 )
* PWM ( D 3 ) PB3 4 | | 37 PA3 ( AI 3 / D28 )
* PWM ( D 4 ) PB4 5 | | 36 PA4 ( AI 4 / D27 )
* MOSI ( D 5 ) PB5 6 | | 35 PA5 ( AI 5 / D26 )
* MISO ( D 6 ) PB6 7 | | 34 PA6 ( AI 6 / D25 )
* SCK ( D 7 ) PB7 8 | | 33 PA7 ( AI 7 / D24 )
* RST 9 | | 32 AREF
* VCC 10 | | 31 GND
* GND 11 | | 30 AVCC
* XTAL2 12 | | 29 PC7 ( D 23 )
* XTAL1 13 | | 28 PC6 ( D 22 )
* RX0 ( D 8 ) PD0 14 | | 27 PC5 ( D 21 ) TDI
* TX0 ( D 9 ) PD1 15 | | 26 PC4 ( D 20 ) TDO
* INT0 RX1 ( D 10 ) PD2 16 | | 25 PC3 ( D 19 ) TMS
* INT1 TX1 ( D 11 ) PD3 17 | | 24 PC2 ( D 18 ) TCK
* PWM ( D 12 ) PD4 18 | | 23 PC1 ( D 17 ) SDA
* PWM ( D 13 ) PD5 19 | | 22 PC0 ( D 16 ) SCL
* PWM ( D 14 ) PD6 20 | | 21 PD7 ( D 15 ) PWM
* + - - - - - - - - +
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 1
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega644P__
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 20
# define ORIG_X_MAX_PIN 21
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 19
# define ORIG_Y_MIN_PIN 25
# define ORIG_Y_MAX_PIN 26
# define ORIG_Z_STEP_PIN 29
# define ORIG_Z_DIR_PIN 30
# define ORIG_Z_ENABLE_PIN 31
# define ORIG_Z_MIN_PIN 2
# define ORIG_Z_MAX_PIN 1
# define ORIG_E0_STEP_PIN 12
# define ORIG_E0_DIR_PIN 16
# define ORIG_E0_ENABLE_PIN 3
# define SDPOWER -1
# define SDSS -1
# define LED_PIN 0
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN -1
# define HEATER_0_PIN 14
2016-01-15 20:42:10 +01:00
//D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
# define TEMP_0_PIN 4
2015-10-16 11:04:50 +02:00
# define HEATER_1_PIN -1
# define TEMP_1_PIN -1
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
# if MOTHERBOARD == 91
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284__)
# error Oops! Make sure you have 'OMC with Atmega644 at 20 Mhz' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 26
# define ORIG_X_DIR_PIN 25
# define ORIG_X_ENABLE_PIN 10
# define ORIG_X_MIN_PIN 0
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 28
# define ORIG_Y_DIR_PIN 27
# define ORIG_Y_ENABLE_PIN 10
# define ORIG_Y_MIN_PIN 1
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 23
# define ORIG_Z_DIR_PIN 22
# define ORIG_Z_ENABLE_PIN 10
# define ORIG_Z_MIN_PIN 2
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 24
# define ORIG_E0_DIR_PIN 21
# define ORIG_E0_ENABLE_PIN 10
# define PROBE_PIN 13
# define SDPOWER -1
# define SDSS -1
# define LED_PIN -1
# define ORIG_FAN_PIN 14
# define ORIG_PS_ON_PIN -1
# define ORIG_SDCARDDETECT -1
# define HEATER_0_PIN 3
# define TEMP_0_PIN 0
# define HEATER_1_PIN 4
# define TEMP_1_PIN 1
# define HEATER_2_PIN -1
# define TEMP_2_PIN 2
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# endif
/****************************************************************************************
* RepRap Motherboard * * * * - - - NOOOOOO RS485 / EXTRUDER CONTROLLER ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! - - - * * * * * * *
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 2
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega644P__
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 20
# define ORIG_X_MAX_PIN 21
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 24
# define ORIG_Y_MIN_PIN 25
# define ORIG_Y_MAX_PIN 26
# define ORIG_Z_STEP_PINN 27
# define ORIG_Z_DIR_PINN 28
# define ORIG_Z_ENABLE_PIN 29
# define ORIG_Z_MIN_PIN 30
# define ORIG_Z_MAX_PIN 31
# define ORIG_E0_STEP_PIN 17
# define ORIG_E0_DIR_PIN 16
# define ORIG_E0_ENABLE_PIN -1
# define SDPOWER -1
# define SDSS 4
# define LED_PIN 0
# define SD_CARD_WRITE 2
# define SD_CARD_DETECT 3
# define SD_CARD_SELECT 4
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
//pin for controlling the PSU.
# define ORIG_PS_ON_PIN 14
# define ORIG_FAN_PIN -1
# define HEATER_0_PIN -1
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
# define TEMP_0_PIN -1
2015-10-16 11:04:50 +02:00
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
/****************************************************************************************
* Gen3 PLUS for RepRap Motherboard V1 .2
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 21
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega644P__
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 20
# define ORIG_X_MAX_PIN -1
//y axis pins
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 24
# define ORIG_Y_MIN_PIN 25
# define ORIG_Y_MAX_PIN -1
//z axis pins
# define ORIG_Z_STEP_PIN 27
# define ORIG_Z_DIR_PIN 28
# define ORIG_Z_ENABLE_PIN 29
# define ORIG_Z_MIN_PIN 30
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_DIR_PIN 21
# define ORIG_E0_STEP_PIN 17
# define ORIG_E0_ENABLE_PIN 13
//heaters
2016-01-15 20:42:10 +01:00
// hot end heater
# define HEATER_0_PIN 12
// heated bed heater
# define HEATER_1_PIN 16
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
//pin for debugging.
# define DEBUG_PIN -1
//SD card pin
# define SDSS 4
# define SDPOWER -1
# define ORIG_FAN_PIN -1
# define TEMP_0_PIN 0
# define TEMP_1_PIN 5
# define LED_PIN -1
//pin for controlling the PSU.
# define ORIG_PS_ON_PIN 14
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
//----------end Gen3 PLUS for RepRap Motherboard V1.2--------------
/****************************************************************************************
* Arduino Mega pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 33
# define KNOWN_BOARD 1
# define RAMPS_V_1_3
# elif MOTHERBOARD == 34
# define KNOWN_BOARD 1
# define RAMPS_V_1_3
# define AZTEEG_X3
# elif MOTHERBOARD == 35
# define KNOWN_BOARD 1
# define RAMPS_V_1_3
# define AZTEEG_X3_PRO
# endif
# if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35
# define KNOWN_BOARD 1
2016-07-02 18:11:43 +02:00
# if !(defined (__AVR_ATmega1280__ ) || defined (__AVR_ATmega2560__ ))
2015-10-16 11:04:50 +02:00
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1
// #define RAMPS_V_1_3
// #define RAMPS_V_1_0
# ifdef RAMPS_V_1_3
# define ORIG_X_STEP_PIN 54
# define ORIG_X_DIR_PIN 55
# define ORIG_X_ENABLE_PIN 38
# define ORIG_X_MIN_PIN 3
# define ORIG_X_MAX_PIN 2
# define ORIG_Y_STEP_PIN 60
# define ORIG_Y_DIR_PIN 61
# define ORIG_Y_ENABLE_PIN 56
# define ORIG_Y_MIN_PIN 14
# define ORIG_Y_MAX_PIN 15
# define ORIG_Z_STEP_PIN 46
# define ORIG_Z_DIR_PIN 48
# define ORIG_Z_ENABLE_PIN 62
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN 19
# define ORIG_E0_STEP_PIN 26
# define ORIG_E0_DIR_PIN 28
# define ORIG_E0_ENABLE_PIN 24
# define ORIG_E1_STEP_PIN 36
# define ORIG_E1_DIR_PIN 34
# define ORIG_E1_ENABLE_PIN 30
# define SDPOWER -1
# define SDSS 53
# define ORIG_SDCARDDETECT 49
# define LED_PIN 13
# define ORIG_FAN_PIN 9
# define ORIG_PS_ON_PIN 12
# define HEATER_0_PIN 10
# define HEATER_1_PIN 8
# define HEATER_2_PIN 9
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING
# define TEMP_0_PIN 13
# define TEMP_1_PIN 14
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN 15
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# else // RAMPS_V_1_1 or RAMPS_V_1_2 as default
# define ORIG_X_STEP_PIN 26
# define ORIG_X_DIR_PIN 28
# define ORIG_X_ENABLE_PIN 24
# define ORIG_X_MIN_PIN 3
# define ORIG_X_MAX_PIN -1 //2
# define ORIG_Y_STEP_PIN 38
# define ORIG_Y_DIR_PIN 40
# define ORIG_Y_ENABLE_PIN 36
# define ORIG_Y_MIN_PIN 16
# define ORIG_Y_MAX_PIN -1 //17
# define ORIG_Z_STEP_PIN 44
# define ORIG_Z_DIR_PIN 46
# define ORIG_Z_ENABLE_PIN 42
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN -1 //19
# define ORIG_E0_STEP_PIN 32
# define ORIG_E0_DIR_PIN 34
# define ORIG_E0_ENABLE_PIN 30
# define SDPOWER 48
# define SDSS 53
# define LED_PIN 13
# define ORIG_PS_ON_PIN -1
//#define SCL 21
//#define SDA 20
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# ifdef RAMPS_V_1_0 // RAMPS_V_1_0
2016-01-15 20:42:10 +01:00
# define HEATER_0_PIN 12
# define HEATER_1_PIN -1
# define ORIG_FAN_PIN 11
2015-10-16 11:04:50 +02:00
# else // RAMPS_V_1_1 or RAMPS_V_1_2
2016-01-15 20:42:10 +01:00
# define HEATER_0_PIN 10
# define HEATER_1_PIN 8
# define ORIG_FAN_PIN 9
2015-10-16 11:04:50 +02:00
# endif
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
# define TEMP_0_PIN 2
# define TEMP_1_PIN 1
2015-10-16 11:04:50 +02:00
# endif
// SPI for Max6675 Thermocouple
// these pins are defined in the SD library if building with SD support
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define MAX6675_SS 53
# ifdef AZTEEG_X3
# define SDSUPPORT 1
# define SDCARDDETECTINVERTED 0
# define ORIG_SDCARDDETECT 49
# define ORIG_FAN_PIN 4
# define ORIG_FAN2_PIN 5
# define LIGHT_PIN 6
2016-01-15 20:42:10 +01:00
// Activate beeper on extension shield
# define BEEPER_PIN 33
2015-10-16 11:04:50 +02:00
# define BEEPER_TYPE 1
2016-01-15 20:42:10 +01:00
// Only available with X3 shield
# define ORIG_E2_STEP_PIN 27
# define ORIG_E2_DIR_PIN 29
# define ORIG_E2_ENABLE_PIN 41
// Only available with X3 shield
# define ORIG_E3_STEP_PIN 23
# define ORIG_E3_DIR_PIN 25
# define ORIG_E3_ENABLE_PIN 40
// Only available with X3 shield
# define HEATER_3_PIN 17
# define TEMP_3_PIN 12
# define HEATER_4_PIN 16
# define TEMP_4_PIN 5
2015-10-16 11:04:50 +02:00
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# define E3_PINS E3_STEP_PIN,E3_DIR_PIN,E3_ENABLE_PIN,
# endif
# ifdef AZTEEG_X3_PRO
# define SDSUPPORT true
# define SDCARDDETECTINVERTED false
# define ORIG_SDCARDDETECT 49
# define SDSS 53
2016-01-15 20:42:10 +01:00
# undef ORIG_FAN_PIN
2015-10-16 11:04:50 +02:00
# define ORIG_FAN_PIN 5
# define ORIG_FAN2_PIN 6
# define LIGHT_PIN 11
2016-01-15 20:42:10 +01:00
// Activate beeper on extension shield
# define BEEPER_PIN 33
2015-10-16 11:04:50 +02:00
# define BEEPER_TYPE 1
# define ORIG_E2_STEP_PIN 23
# define ORIG_E2_DIR_PIN 25
# define ORIG_E2_ENABLE_PIN 40
# define ORIG_E3_STEP_PIN 27
# define ORIG_E3_DIR_PIN 29
# define ORIG_E3_ENABLE_PIN 41
# define ORIG_E4_STEP_PIN 43
# define ORIG_E4_DIR_PIN 37
# define ORIG_E4_ENABLE_PIN 42
# define HEATER_0_PIN 10
2016-01-15 20:42:10 +01:00
// bed
# define HEATER_1_PIN 8
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN 9
# define HEATER_3_PIN 16
# define HEATER_4_PIN 17
# define HEATER_5_PIN 4
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING
# define TEMP_0_PIN 13
// BED , ANALOG NUMBERING
# define TEMP_1_PIN 14
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN 15
2016-01-15 20:42:10 +01:00
# define TEMP_3_PIN 12
# define TEMP_4_PIN 11
2015-10-16 11:04:50 +02:00
# define TEMP_5_PIN 10
2016-01-15 20:42:10 +01:00
// Thermocouple 1 and 2
# define TEMP_6_PIN 4
# define TEMP_7_PIN 5
# define THERMOCOUPLE_0_PIN 4
# define THERMOCOUPLE_1_PIN 5
2015-10-16 11:04:50 +02:00
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# define E3_PINS ORIG_E3_STEP_PIN,ORIG_E3_DIR_PIN,ORIG_E3_ENABLE_PIN,
# define E4_PINS ORIG_E4_STEP_PIN,ORIG_E4_DIR_PIN,ORIG_E4_ENABLE_PIN,
# endif
# endif
/****************************************************************************************
* Ultimaker Shield pin assignment v1 .5 .7
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 37
# define ULTIMAKER_157
# define KNOWN_BOARD 1
# define ORIG_X_STEP_PIN 25
# define ORIG_X_DIR_PIN 23
# define ORIG_X_MIN_PIN 22
# define ORIG_X_MAX_PIN 24
# define ORIG_X_ENABLE_PIN 27
# define ORIG_Y_STEP_PIN 31
# define ORIG_Y_DIR_PIN 33
# define ORIG_Y_MIN_PIN 26
# define ORIG_Y_MAX_PIN 28
# define ORIG_Y_ENABLE_PIN 29
# define ORIG_Z_STEP_PIN 37
# define ORIG_Z_DIR_PIN 39
# define ORIG_Z_MIN_PIN 30
# define ORIG_Z_MAX_PIN 32
# define ORIG_Z_ENABLE_PIN 35
2016-01-15 20:42:10 +01:00
// bed
# define HEATER_1_PIN 4
2015-10-16 11:04:50 +02:00
# define TEMP_1_PIN 10
2016-01-15 20:42:10 +01:00
# define HEATER_0_PIN 2
# define TEMP_0_PIN 8
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN 3
# define TEMP_2_PIN 9
# define HEATER_3_PIN -1
# define TEMP_3_PIN -1
# define ORIG_E0_STEP_PIN 43
# define ORIG_E0_DIR_PIN 45
# define ORIG_E0_ENABLE_PIN 41
# define E0_FAN_PIN -1
// #define EXT1_EXTRUDER_COOLER_PIN E0_FAN_PIN
# define ORIG_E1_STEP_PIN 49
# define ORIG_E1_DIR_PIN 47
# define ORIG_E1_ENABLE_PIN 48
# define E1_FAN_PIN -1
// #define EXT2_EXTRUDER_COOLER_PIN E1_FAN_PIN
# define LED_PIN 13
# define ORIG_FAN_PIN 7
# define ORIG_PS_ON_PIN 12
# define KILL_PIN -1
2016-01-15 20:42:10 +01:00
//PIN that has to be turned on right after start, to keep power flowing.
# define SUICIDE_PIN 54
2015-10-16 11:04:50 +02:00
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define SDPOWER -1
# define SDSS 53
2016-01-15 20:42:10 +01:00
# define ORIG_SDCARDDETECT 38
2015-10-16 11:04:50 +02:00
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# endif
/****************************************************************************************
* RUMBA pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 80
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 17
# define ORIG_X_DIR_PIN 16
# define ORIG_X_ENABLE_PIN 48
# define ORIG_X_MIN_PIN 37
2016-01-15 20:42:10 +01:00
# define ORIG_X_MAX_PIN 36
2015-10-16 11:04:50 +02:00
# define ORIG_Y_STEP_PIN 54
# define ORIG_Y_DIR_PIN 47
# define ORIG_Y_ENABLE_PIN 55
# define ORIG_Y_MIN_PIN 35
# define ORIG_Y_MAX_PIN 34
# define ORIG_Z_STEP_PIN 57
# define ORIG_Z_DIR_PIN 56
# define ORIG_Z_ENABLE_PIN 62
# define ORIG_Z_MIN_PIN 33
# define ORIG_Z_MAX_PIN 32
# define ORIG_E0_STEP_PIN 23
# define ORIG_E0_DIR_PIN 22
# define ORIG_E0_ENABLE_PIN 24
# define ORIG_E1_STEP_PIN 26
# define ORIG_E1_DIR_PIN 25
# define ORIG_E1_ENABLE_PIN 27
# define ORIG_E2_STEP_PIN 29
# define ORIG_E2_DIR_PIN 28
# define ORIG_E2_ENABLE_PIN 39
# define LED_PIN 13
# define ORIG_FAN_PIN 7
# define ORIG_FAN2_PIN 8 // (e.g. useful for electronics fan or light on/off) on PIN 8
# define ORIG_PS_ON_PIN 45
2016-01-15 20:42:10 +01:00
// EXTRUDER 1
# define HEATER_0_PIN 2
// EXTRUDER 2
# define HEATER_2_PIN 3
// EXTRUDER 3
# define HEATER_3_PIN 6
2015-10-16 11:04:50 +02:00
//optional FAN1 can be used as 4th heater output: #define HEATER_4_PIN 8 // EXTRUDER 4
2016-01-15 20:42:10 +01:00
// BED
# define HEATER_1_PIN 9
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING
# define TEMP_0_PIN 15
# define TEMP_2_PIN 14
# define TEMP_3_PIN 13
2015-10-16 11:04:50 +02:00
//optional for extruder 4 or chamber: #define TEMP_2_PIN 12 // ANALOG NUMBERING
2016-01-15 20:42:10 +01:00
# define TEMP_1_PIN 11
2015-10-16 11:04:50 +02:00
# define SDPOWER -1
# define SDSS 53
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# endif //MOTHERBOARD==80
/****************************************************************************************
* Duemilanove w / ATMega328P pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 4
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega328P__
# error Oops! Make sure you have 'Arduino Duemilanove w / ATMega328' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 19
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN -1
# define ORIG_X_MIN_PIN 17
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 10
# define ORIG_Y_DIR_PIN 7
# define ORIG_Y_ENABLE_PIN -1
# define ORIG_Y_MIN_PIN 8
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 13
# define ORIG_Z_DIR_PIN 3
# define ORIG_Z_ENABLE_PIN 2
# define ORIG_Z_MIN_PIN 4
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 11
# define ORIG_E0_DIR_PIN 12
# define ORIG_E0_ENABLE_PIN -1
# define SDPOWER -1
# define SDSS -1
# define LED_PIN -1
# define ORIG_FAN_PIN 5
# define ORIG_PS_ON_PIN -1
# define HEATER_0_PIN 6
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
# define TEMP_0_PIN 0
2015-10-16 11:04:50 +02:00
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
/****************************************************************************************
* Gen6 pin assignment ( 5 ) and Gen6 deluxe assignment ( 51 )
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 5 || MOTHERBOARD == 51
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 20
# define ORIG_X_MAX_PIN -1
//y axis pins
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 24
# define ORIG_Y_MIN_PIN 25
# define ORIG_Y_MAX_PIN -1
//z axis pins
# define ORIG_Z_STEP_PIN 27
# define ORIG_Z_DIR_PIN 28
# define ORIG_Z_ENABLE_PIN 29
# define ORIG_Z_MIN_PIN 30
# define ORIG_Z_MAX_PIN -1
//extruder pins
2016-01-15 20:42:10 +01:00
# define ORIG_E0_STEP_PIN 4
# define ORIG_E0_DIR_PIN 2
# define ORIG_E0_ENABLE_PIN 3
# define TEMP_0_PIN 5
# define HEATER_0_PIN 14
2015-10-16 11:04:50 +02:00
# if MOTHERBOARD == 5
2016-01-15 20:42:10 +01:00
# define HEATER_1_PIN -1
# define TEMP_1_PIN -1
2015-10-16 11:04:50 +02:00
# else
2016-01-15 20:42:10 +01:00
# define HEATER_1_PIN 1
# define TEMP_1_PIN 0
2015-10-16 11:04:50 +02:00
# endif
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
2016-01-15 20:42:10 +01:00
// SCL pin of I2C header
# define SDSS 16
# define LED_PIN -1
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN -1
2015-10-16 11:04:50 +02:00
//our pin for debugging.
# define DEBUG_PIN 0
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
// #define SCL 16
// #define SDA 17
# endif
/****************************************************************************************
* Sanguinololu pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 62
# define SANGUINOLOLU_V_1_2
# endif
# if MOTHERBOARD == 65
# define AZTEEG_X1
# define SANGUINOLOLU_V_1_2
# endif
# if MOTHERBOARD == 6 || MOTHERBOARD == 62 || MOTHERBOARD == 65
# define KNOWN_BOARD 1
//#ifndef __AVR_ATmega644P__
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 21
# define ORIG_X_MIN_PIN 18
# define ORIG_X_MAX_PIN -2
# define ORIG_Y_STEP_PIN 22
# define ORIG_Y_DIR_PIN 23
# define ORIG_Y_MIN_PIN 19
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 3
# define ORIG_Z_DIR_PIN 2
# define ORIG_Z_MIN_PIN 20
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 1
# define ORIG_E0_DIR_PIN 0
# define LED_PIN -1
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN -1
2016-01-15 20:42:10 +01:00
// (extruder)
# define HEATER_0_PIN 13
2015-10-16 11:04:50 +02:00
# ifdef SANGUINOLOLU_V_1_2
2016-01-15 20:42:10 +01:00
// (bed)
# define HEATER_1_PIN 12
2015-10-16 11:04:50 +02:00
# define ORIG_X_ENABLE_PIN 14
# define ORIG_Y_ENABLE_PIN 14
# define ORIG_Z_ENABLE_PIN 26
# define ORIG_E0_ENABLE_PIN 14
# else
# define HEATER_1_PIN 14 // (bed)
# define ORIG_X_ENABLE_PIN -1
# define ORIG_Y_ENABLE_PIN -1
# define ORIG_Z_ENABLE_PIN -1
# define ORIG_E0_ENABLE_PIN -1
# endif
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
# define TEMP_0_PIN 7
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
# define TEMP_1_PIN 6
2015-10-16 11:04:50 +02:00
# define SDPOWER -1
# define SDSS 31
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# ifdef AZTEEG_X1
# define ORIG_FAN_PIN 4
# endif
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# define E2_PINS
# ifndef KNOWN_BOARD
# error Unknown MOTHERBOARD value in configuration.h
# endif
# endif
/****************************************************************************************
* Melzi pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 63
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega644P__
# ifndef __AVR_ATmega1284P__
//#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
# endif
# define ORIG_X_STEP_PIN 15
# define ORIG_X_DIR_PIN 21
# define ORIG_X_MIN_PIN 18
# define ORIG_X_MAX_PIN -2
# define ORIG_Y_STEP_PIN 22
# define ORIG_Y_DIR_PIN 23
# define ORIG_Y_MIN_PIN 19
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 3
# define ORIG_Z_DIR_PIN 2
# define ORIG_Z_MIN_PIN 20
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 1
# define ORIG_E0_DIR_PIN 0
# define ORIG_E0_ENABLE_PIN 14
2016-01-15 20:42:10 +01:00
//29 on Melzi1284p A2
# define PROBE_PIN -1
2015-10-16 11:04:50 +02:00
# define LED_PIN 27
# define ORIG_FAN_PIN 4
# define ORIG_PS_ON_PIN -1
2016-01-15 20:42:10 +01:00
// (extruder)
# define HEATER_0_PIN 13
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN -1
2016-01-15 20:42:10 +01:00
// bed (change to 12 for breakout pin on header)
# define HEATER_1_PIN 10
2016-07-02 18:11:43 +02:00
2015-10-16 11:04:50 +02:00
# define ORIG_X_ENABLE_PIN 14
# define ORIG_Y_ENABLE_PIN 14
# define ORIG_Z_ENABLE_PIN 26
2016-01-15 20:42:10 +01:00
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
# define TEMP_0_PIN 7
// MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
# define TEMP_1_PIN 6
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN -1
# define SDPOWER -1
2016-01-15 20:42:10 +01:00
// 31 http://reprap.org/wiki/Melzi#Melzi_Arduino_Pin_Numbers says 31, schamtic show pin 37 = PA0 which is arduino pin 31!
# define SDSS 31
2015-10-16 11:04:50 +02:00
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
# define SDSUPPORT 1 // sd card reader on board
# define ORIG_SDCARDDETECT -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
2016-01-15 20:42:10 +01:00
# if MOTHERBOARD == 66
2016-07-02 18:11:43 +02:00
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
// X/Y/Z Steppers and MIN endstops verified
# define ORIG_X_STEP_PIN 54
# define ORIG_X_DIR_PIN 55
# define ORIG_X_ENABLE_PIN 38
# define ORIG_X_MIN_PIN 3
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 60
# define ORIG_Y_DIR_PIN 61
# define ORIG_Y_ENABLE_PIN 56
# define ORIG_Y_MIN_PIN 14
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 46
# define ORIG_Z_DIR_PIN 48
# define ORIG_Z_ENABLE_PIN 63
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 26
# define ORIG_E0_DIR_PIN 28
# define ORIG_E0_ENABLE_PIN 24
# define ORIG_E1_STEP_PIN -1
# define ORIG_E1_DIR_PIN -1
# define ORIG_E1_ENABLE_PIN -1
# define SDPOWER -1
# define SDSS 25
# define ORIG_SDCARDDETECT -1
# define LED_PIN 13
# define ORIG_FAN_PIN 8
# define ORIG_PS_ON_PIN -1
// schematic: HEATER1 (Extruder)
# define HEATER_0_PIN 10
// schematic: HEATER2 (Heated Bed)
# define HEATER_1_PIN 9
# define HEATER_2_PIN -1
// ANALOG NUMBERING
// schematic: THERM1 (Extruder)
# define TEMP_0_PIN 13
// schematic: THERM2 (Heated Bed)
# define TEMP_1_PIN 14
# define TEMP_2_PIN -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
// following pins (LCD, ENCODER, SDCARD) reverse engineered from schematic diagram:
# ifdef ULTRA_LCD
# ifdef NEWPANEL
# define LCD_PINS_RS 27
# define LCD_PINS_ENABLE 29
# define LCD_PINS_D4 37
# define LCD_PINS_D5 35
# define LCD_PINS_D6 33
# define LCD_PINS_D7 31
# define BTN_EN1 16
# define BTN_EN2 17
# define BTN_ENC 23
# endif
# endif //ULTRA_LCD
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
2016-01-15 20:42:10 +01:00
# define MAX6675_SS 53
# endif
2015-10-16 11:04:50 +02:00
/****************************************************************************************
* Gen7 1.1 and above pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 7
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 19
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 24
# define ORIG_X_MIN_PIN 7
# define ORIG_X_MAX_PIN 6
//y axis pins
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 24
# define ORIG_Y_MIN_PIN 5
# define ORIG_Y_MAX_PIN 2
//z axis pins
# define ORIG_Z_STEP_PIN 26
# define ORIG_Z_DIR_PIN 25
# define ORIG_Z_ENABLE_PIN 24
# define ORIG_Z_MIN_PIN 1
# define ORIG_Z_MAX_PIN 0
//extruder pins
# define ORIG_E0_STEP_PIN 28
# define ORIG_E0_DIR_PIN 27
# define ORIG_E0_ENABLE_PIN 24
# define TEMP_0_PIN 1
# define TEMP_1_PIN 2
# define HEATER_0_PIN 4
# define HEATER_1_PIN 3
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
# define SDSS -1 // SCL pin of I2C header
# define LED_PIN -1
# define ORIG_FAN_PIN 31
# define ORIG_PS_ON_PIN 15
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
//our pin for debugging.
# define DEBUG_PIN 0
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
# define SCK_PIN 7
# define SDSSORIG 4
# define MISO_PIN 6
# define MOSI_PIN 5
# endif
/****************************************************************************************
* Gen7 1.4 .1 pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 71
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 29
# define ORIG_X_DIR_PIN 28
# define ORIG_X_ENABLE_PIN 25
# define ORIG_X_MIN_PIN 0
# define ORIG_X_MAX_PIN -1
//y axis pins
# define ORIG_Y_STEP_PIN 27
# define ORIG_Y_DIR_PIN 26
# define ORIG_Y_ENABLE_PIN 25
# define ORIG_Y_MIN_PIN 1
# define ORIG_Y_MAX_PIN -1
//z axis pins
# define ORIG_Z_STEP_PIN 23
# define ORIG_Z_DIR_PIN 22
# define ORIG_Z_ENABLE_PIN 25
# define ORIG_Z_MIN_PIN 2
# define ORIG_Z_MAX_PIN -1
//extruder pins
# define ORIG_E0_STEP_PIN 19
# define ORIG_E0_DIR_PIN 18
# define ORIG_E0_ENABLE_PIN 25
# define TEMP_0_PIN 1
# define TEMP_1_PIN 0
# define HEATER_0_PIN 4
# define HEATER_1_PIN 3
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
# define SDSS -1
# define LED_PIN -1
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN 15
//our pin for debugging.
# define DEBUG_PIN 0
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
# define SDPOWER -1
# define SDSS -1
2016-01-15 20:42:10 +01:00
// Needs to set this to output to enable SPI even if other SS is used!
# define SDSSORIG 4
2015-10-16 11:04:50 +02:00
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
/****************************************************************************************
* Sethi 3 D_1 Extruder
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 72
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Sethi' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 19
# define ORIG_X_DIR_PIN 18
# define ORIG_X_ENABLE_PIN 24
# define ORIG_X_MIN_PIN 2
# define ORIG_X_MAX_PIN 6
//y axis pins
# define ORIG_Y_STEP_PIN 23
# define ORIG_Y_DIR_PIN 22
# define ORIG_Y_ENABLE_PIN 24
# define ORIG_Y_MIN_PIN 0
# define ORIG_Y_MAX_PIN 2
//z axis pins
# define ORIG_Z_STEP_PIN 26
# define ORIG_Z_DIR_PIN 25
# define ORIG_Z_ENABLE_PIN 24
# define ORIG_Z_MIN_PIN 1
# define ORIG_Z_MAX_PIN 0
//extruder pins
# define ORIG_E0_STEP_PIN 28
# define ORIG_E0_DIR_PIN 27
# define ORIG_E0_ENABLE_PIN 24
# define TEMP_0_PIN 1
# define TEMP_1_PIN 2
# define HEATER_0_PIN 4
# define HEATER_1_PIN 3
# define SDPOWER -1
# define SDSS -1 // SCL pin of I2C header
# define LED_PIN -1
# define ORIG_FAN_PIN 31
# define ORIG_PS_ON_PIN 15
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
//our pin for debugging.
# define DEBUG_PIN 0
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
# define SCK_PIN 7
# define SDSSORIG 4
# define MISO_PIN 6
# define MOSI_PIN 5
# endif
/****************************************************************************************
OpenHardware . co . za FrontPrint Controller 1.0
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 73
# define KNOWN_BOARD 1
# if !defined(AVR_ATmega644P) && !defined(AVR_ATmega644) && !defined(AVR_ATmega1284P)
# error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 29
# define ORIG_X_DIR_PIN 28
# define ORIG_X_ENABLE_PIN 25
# define ORIG_X_MIN_PIN 0
# define ORIG_X_MAX_PIN -1
//y axis pins
# define ORIG_Y_STEP_PIN 27
# define ORIG_Y_DIR_PIN 26
# define ORIG_Y_ENABLE_PIN 25
# define ORIG_Y_MIN_PIN 1
# define ORIG_Y_MAX_PIN -1
//z axis pins
# define ORIG_Z_STEP_PIN 23
# define ORIG_Z_DIR_PIN 22
# define ORIG_Z_ENABLE_PIN 25
# define ORIG_Z_MIN_PIN 2
# define ORIG_Z_MAX_PIN -1
//First extruder pins
# define ORIG_E0_STEP_PIN 19
# define ORIG_E0_DIR_PIN 18
# define ORIG_E0_ENABLE_PIN 25
# define TEMP_0_PIN 1
# define HEATER_0_PIN 4
//Second Extruder pins
# define ORIG_E1_STEP_PIN 20
# define ORIG_E1_DIR_PIN 18
# define ORIG_E1_ENABLE_PIN 25
# define TEMP_2_PIN 7
# define HEATER_2_PIN 13
//Heated Bed Pins
# define HEATER_1_PIN 3
# define TEMP_1_PIN 0
//SD Card Pins
# define SDPOWER -1
# define SDSS 14
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
2016-01-15 20:42:10 +01:00
//FAN and ATX Power Supply Control Pins
# define ORIG_FAN_PIN 21
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN 15
# define LED_PIN -1
# define SDSUPPORT 1 // sd card reader on board
# define ORIG_SDCARDDETECT -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# endif
/****************************************************************************************
* Teensylu 0.7 pin assingments ( ATMEGA90USB )
* Requires the Teensyduino software with Teensy2 .0 + + selected in arduino IDE !
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 8
# define KNOWN_BOARD 1
# define ORIG_X_STEP_PIN 28
# define ORIG_X_DIR_PIN 29
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 25
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 30
# define ORIG_Y_DIR_PIN 31
2016-01-15 20:42:10 +01:00
# define ORIG_Y_ENABLE_PIN 20
# define ORIG_Y_MIN_PIN 26
2015-10-16 11:04:50 +02:00
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 32
# define ORIG_Z_DIR_PIN 33
# define ORIG_Z_ENABLE_PIN 17
# define ORIG_Z_MIN_PIN 27
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 34
# define ORIG_E0_DIR_PIN 35
# define ORIG_E0_ENABLE_PIN 13
2016-01-15 20:42:10 +01:00
// Extruder - ANALOG PIN NUMBER!
# define TEMP_0_PIN 7
// Bed - ANALOG PIN NUMBER!
# define TEMP_1_PIN 6
// Extruder
# define HEATER_0_PIN 15
// bed
# define HEATER_1_PIN 14
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
# define SDSS 20
# define LED_PIN -1
# define ORIG_FAN_PIN 16 // Fan
# define ORIG_PS_ON_PIN -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# if !SDSUPPORT
// these pins are defined in the SD library if building with SD support
# define SCK_PIN 21
# define MISO_PIN 23
# define MOSI_PIN 22
# endif
# endif
/****************************************************************************************
* Unique One rev . A pin assingments ( ATMEGA90USB )
* Requires the Teensyduino software with Teensy2 .0 + + selected in arduino IDE !
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 88
# define KNOWN_BOARD 1
# define ORIG_X_STEP_PIN 28
# define ORIG_X_DIR_PIN 29
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 25
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 30
# define ORIG_Y_DIR_PIN 31
# define ORIG_Y_ENABLE_PIN 18
# define ORIG_Y_MIN_PIN 26
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 32
# define ORIG_Z_DIR_PIN 33
# define ORIG_Z_ENABLE_PIN 17
# define ORIG_Z_MIN_PIN 27
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 34
# define ORIG_E0_DIR_PIN 35
# define ORIG_E0_ENABLE_PIN 12
2016-01-15 20:42:10 +01:00
// Extruder
# define HEATER_0_PIN 8
// Extruder - ANALOG PIN NUMBER!
# define TEMP_0_PIN 5
2015-10-16 11:04:50 +02:00
# define ORIG_E1_STEP_PIN 14
# define ORIG_E1_DIR_PIN 13
# define ORIG_E1_ENABLE_PIN 11
2016-01-15 20:42:10 +01:00
// Extruder
# define HEATER_2_PIN 9
// Extruder - ANALOG PIN NUMBER!
# define TEMP_2_PIN 6
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// bed
# define HEATER_1_PIN 10
// Bed - ANALOG PIN NUMBER!
# define TEMP_1_PIN 7
2015-10-16 11:04:50 +02:00
# define SDPOWER -1
# define SDSS 20
# define LED_PIN -1
2016-01-15 20:42:10 +01:00
// Fan
# define ORIG_FAN_PIN 16
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# if !SDSUPPORT
// these pins are defined in the SD library if building with SD support
# define SCK_PIN 21
# define MISO_PIN 23
# define MOSI_PIN 22
# endif
# endif
/****************************************************************************************
* Printrboard Rev . F pin assingments ( ATMEGA90USB1286 )
* Requires the Teensyduino software with Teensy2 .0 + + selected in arduino IDE !
* See http : //reprap.org/wiki/Printrboard for more info
*
* Rev . F uses an MCP4728 DAC to generate the Reference Voltage used to determine the
* Stepper Driver ' s maximum current .
*
* On PrintrBoard , with Sense Resistors = 0.11 Ohms , and 2 Amps maximum current rating ,
* the Maximum VRef to send is calculated as :
*
* 2.00 Amps Maximum Output * ( 8 * 0.11 Ohms ) = 1.76 Maximum VRef from MCP4728 .
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 92
# define KNOWN_BOARD 1
// Definition for current control
# define STEPPER_CURRENT_CONTROL CURRENT_CONTROL_MCP4728
# define MCP4728_I2C_ADDRESS 0x60 << 1 // Base Address (0x60); Pre-Shifted Left 1 bit for Repetier HAL.
# define MCP4728_GENERALCALL_ADDRESS 0x00 // General Call Address. Weird, but OK...
# define MCP4728_CMD_MULTI_WRITE 0B01000000 // Writes DAC Settings, Does not update EEPROM.
# define MCP4728_CMD_SEQ_WRITE 0B01010000 // Writes DAC Settings, also persists to EEPROM.
# define MCP4728_CMD_GC_UPDATE 0B00001000 // General Call Update - Update all DAC Outputs (Only way to update DAC Outputs on PrintrBoard Rev F because they tied /LDAC to VDD.
# define MCP4728_CMD_GC_RESET 0B00000110 // General Call Reset
# define MCP4728_VREF 1 // From DataSheet. We will use MCP4728's internal 2.048V as Vref
# define MCP4728_GAIN 0 // From DataSheet. Use 1x Gain Multiplier (0V - 2.048V);
# define MCP4728_NUM_CHANNELS 4 // Duh. Specified here in case there's a beefier chip used on some other board someday.
# define MCP4728_STEPPER_ORDER {3,2,1,0} // PrintrBoard wired 'em up backwards. SMH. X, Y, Z, E
# define MCP4728_VOUT_MAX 3520 // 1.76 Volts * 2000. See DataSheets for the math. Value should be between 0-4095
# define ORIG_X_STEP_PIN 28
# define ORIG_X_DIR_PIN 29
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 47
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 30
# define ORIG_Y_DIR_PIN 31
# define ORIG_Y_ENABLE_PIN 18
2016-01-15 20:42:10 +01:00
// (Was Pin 20 on Rev B-E); Don't use this if you want to use SD card. Use 37 and put the endstop in the e-stop slot!!!
# define ORIG_Y_MIN_PIN 24
2015-10-16 11:04:50 +02:00
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 32
# define ORIG_Z_DIR_PIN 33
# define ORIG_Z_ENABLE_PIN 17
# define ORIG_Z_MIN_PIN 36
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 34
# define ORIG_E0_DIR_PIN 35
# define ORIG_E0_ENABLE_PIN 13
2016-01-15 20:42:10 +01:00
// Extruder - ANALOG PIN NUMBER!
# define TEMP_0_PIN 1
// Bed - ANALOG PIN NUMBER!
# define TEMP_1_PIN 0
// Extruder
# define HEATER_0_PIN 15
// bed
# define HEATER_1_PIN 14
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
2016-01-15 20:42:10 +01:00
// (Was Pin 26 on Rev. B-E); old value 2
# define SDSS 20
2015-10-16 11:04:50 +02:00
# define LED_PIN -1
2016-01-15 20:42:10 +01:00
// Fan
# define ORIG_FAN_PIN 16
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# if !SDSUPPORT
// these pins are defined in the SD library if building with SD support
# define SCK_PIN 21
# define MISO_PIN 23
# define MOSI_PIN 22
# endif
# endif
/****************************************************************************************
* Printrboard Rev . B pin assingments ( ATMEGA90USB1286 )
* Requires the Teensyduino software with Teensy2 .0 + + selected in arduino IDE !
* See http : //reprap.org/wiki/Printrboard for more info
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 9
# define KNOWN_BOARD 1
# define ORIG_X_STEP_PIN 28
# define ORIG_X_DIR_PIN 29
# define ORIG_X_ENABLE_PIN 19
# define ORIG_X_MIN_PIN 47
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 30
# define ORIG_Y_DIR_PIN 31
# define ORIG_Y_ENABLE_PIN 18
2016-01-15 20:42:10 +01:00
// Don't use this if you want to use SD card. Use 37 and put the endstop in the e-stop slot!!!
# define ORIG_Y_MIN_PIN 20
2015-10-16 11:04:50 +02:00
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 32
# define ORIG_Z_DIR_PIN 33
# define ORIG_Z_ENABLE_PIN 17
# define ORIG_Z_MIN_PIN 36
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 34
# define ORIG_E0_DIR_PIN 35
# define ORIG_E0_ENABLE_PIN 13
2016-01-15 20:42:10 +01:00
// Extruder - ANALOG PIN NUMBER!
# define TEMP_0_PIN 1
// Bed - ANALOG PIN NUMBER!
# define TEMP_1_PIN 0
// Extruder
# define HEATER_0_PIN 15
// bed
# define HEATER_1_PIN 14
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN -1
# define TEMP_2_PIN -1
# define SDPOWER -1
2016-01-15 20:42:10 +01:00
// old value 2
# define SDSS 26
2015-10-16 11:04:50 +02:00
# define LED_PIN -1
2016-01-15 20:42:10 +01:00
# define ORIG_FAN_PIN 16
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN -1
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# if !SDSUPPORT
// these pins are defined in the SD library if building with SD support
# define SCK_PIN 21
# define MISO_PIN 23
# define MOSI_PIN 22
# endif
# endif
/****************************************************************************************
* 3 D Master pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 12
# define KNOWN_BOARD 1
# if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
// Definition for current control
# define STEPPER_CURRENT_CONTROL CURRENT_CONTROL_LTC2600
# define LTC2600_CHANNELS {0x30,0x31,0x32,0x33,0x34}
# define LTC2600_NUM_CHANNELS 5
# define LTC2600_CS_PIN 92 // PIND.4, 47, DA_CS
# define LTC2600_SCK_PIN 93 // PIND.5, 48, DA_SCK
# define LTC2600_SDI_PIN 94 // PIND.6, 49, DA_SDI
// On board beeper, so define values already here
# define BEEPER_PIN 23
# define BEEPER_TYPE 1
# define SDSUPPORT 1 // sd card reader on board
# define ORIG_SDCARDDETECT -1
// digital pin mappings
2016-01-15 20:42:10 +01:00
// PINF.0, 97, STP_DRV1
# define ORIG_X_STEP_PIN 54
// PINF.1, 96, DIR_DRV1
# define ORIG_X_DIR_PIN 55
// PIND.7, 50, ENA_DRV1
# define ORIG_X_ENABLE_PIN 38
// PINE.5, 7, OPTO1
# define ORIG_X_MIN_PIN 3
2015-10-16 11:04:50 +02:00
# define ORIG_X_MAX_PIN -1 // PINJ.0, 63, OPTO4 (would be "15", -1 = disabled)
2016-01-15 20:42:10 +01:00
// PINF.6, 91, STP_DRV2
# define ORIG_Y_STEP_PIN 60
// PINF.7, 90, DIR_DRV2
# define ORIG_Y_DIR_PIN 61
// PINF.2, 95, ENA_DRV2
# define ORIG_Y_ENABLE_PIN 56
// PINE.4, 6, OPTO2
# define ORIG_Y_MIN_PIN 2
// PIND.3, 46, OPTO5 (would be "18", -1 = disabled
# define ORIG_Y_MAX_PIN -1
// PINL.3, 38, STP_DRV3
# define ORIG_Z_STEP_PIN 46
// PINL.1, 36, DIR_DRV3
# define ORIG_Z_DIR_PIN 48
// PINK.0, 89, ENA_DRV3
# define ORIG_Z_ENABLE_PIN 62
// PINJ.1, 64, OPTO3
# define ORIG_Z_MIN_PIN 14
2015-10-16 11:04:50 +02:00
# define ORIG_Z_MAX_PIN -1 // PIND.2, 45, OPTO6 (would be "19", -1 = disabled)
2016-01-15 20:42:10 +01:00
// PINA.4, 74, STP_DRV4
# define ORIG_E0_STEP_PIN 26
// PINA.6, 72, DIR_DRV4
# define ORIG_E0_DIR_PIN 28
// PINA.2, 76 ENA_DRV4
# define ORIG_E0_ENABLE_PIN 24
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// PINC.1, 54, STP_DRV5
# define ORIG_E1_STEP_PIN 36
// PINC.3, 56, DIR_DRV5
# define ORIG_E1_DIR_PIN 34
// PINC.7, 60, ENA_DRV5
# define ORIG_E1_ENABLE_PIN 30
2015-10-16 11:04:50 +02:00
# define SDPOWER -1
2016-01-15 20:42:10 +01:00
// PINB.0, 19, SS
# define SDSS 53
// PINB.7, 26, LED13
# define LED_PIN 13
// OUT1 PINA.3, 75, OUT1
# define ORIG_FAN_PIN 25
// OUT2
# define FAN_BOARD_PIN 27
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN -1
2016-01-15 20:42:10 +01:00
// PINB.4, 23, HZ1
# define HEATER_0_PIN 10
// PINH.6, 18, HZ2
# define HEATER_1_PIN 9
// PINH.5, 17, HZ3
# define HEATER_2_PIN 8
2015-10-16 11:04:50 +02:00
// analog pin mappings
2016-01-15 20:42:10 +01:00
// PINK.5, 84, TH1
# define TEMP_0_PIN 13
// PINK.6, 83, TH2
# define TEMP_1_PIN 14
// PINK.7, 82, TH3
# define TEMP_2_PIN 15
2015-10-16 11:04:50 +02:00
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
// these pins are defined in the SD library if building with SD support
2016-01-15 20:42:10 +01:00
// PINB.1, 20, SCK
# define SCK_PIN 52
// PINB.3, 22, MISO
# define MISO_PIN 50
// PINB.2, 21, MOSI
# define MOSI_PIN 51
// PINB.0, 19, SS
# define MAX6675_SS 53
2015-10-16 11:04:50 +02:00
# endif // MOTHERBOARD == 12
/****************************************************************************************
* MegaTronics
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 70
# define KNOWN_BOARD 1
//////////////////FIX THIS//////////////
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 26
# define ORIG_X_DIR_PIN 28
# define ORIG_X_ENABLE_PIN 24
# define ORIG_X_MIN_PIN 41
2016-01-15 20:42:10 +01:00
//2 //Max endstops default to disabled "-1", set to commented value to enable.
# define ORIG_X_MAX_PIN 37
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Y_STEP_PIN 60
# define ORIG_Y_DIR_PIN 61
2015-10-16 11:04:50 +02:00
# define ORIG_Y_ENABLE_PIN 22
# define ORIG_Y_MIN_PIN 14
2016-01-15 20:42:10 +01:00
# define ORIG_Y_MAX_PIN 15
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Z_STEP_PIN 54
# define ORIG_Z_DIR_PIN 55
# define ORIG_Z_ENABLE_PIN 56
2015-10-16 11:04:50 +02:00
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN 19
# define ORIG_E0_STEP_PIN 31
# define ORIG_E0_DIR_PIN 32
# define ORIG_E0_ENABLE_PIN 38
# define ORIG_E1_STEP_PIN 34
# define ORIG_E1_DIR_PIN 36
# define ORIG_E1_ENABLE_PIN 30
# define SDPOWER -1
# define SDSS 53
# define LED_PIN 13
2016-01-15 20:42:10 +01:00
// IO pin. Buffer needed
# define ORIG_FAN_PIN 7
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN 12
2016-01-15 20:42:10 +01:00
// EXTRUDER 1
# define HEATER_0_PIN 9
// EXTRUDER 2 (FAN On Sprinter)
# define HEATER_1_PIN 8
// Heated bed
# define HEATER_2_PIN 10
2015-10-16 11:04:50 +02:00
# define THERMOCOUPLE_0_PIN 8
2016-01-15 20:42:10 +01:00
// Thermocouple 0 ANALOG NUMBERING
# define TEMP_3_PIN 8
// ANALOG NUMBERING
# define TEMP_0_PIN 13
// ANALOG NUMBERING
# define TEMP_1_PIN 15
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN -1 // ANALOG NUMBERING
2016-01-15 20:42:10 +01:00
// BED
# define HEATER_BED_PIN 10
// ANALOG NUMBERING
# define TEMP_BED_PIN 14
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// Beeper on AUX-4
# define BEEPER_PIN 33
2015-10-16 11:04:50 +02:00
# define BEEPER_TYPE 1
# define SDSUPPORT 1 // sd card reader on board
# define ORIG_SDCARDDETECT -1
# ifdef ULTRA_LCD
# ifdef NEWPANEL
# define LCD_PINS_RS 16
# define LCD_PINS_ENABLE 17
# define LCD_PINS_D4 23
# define LCD_PINS_D5 25
# define LCD_PINS_D6 27
# define LCD_PINS_D7 29
//buttons are directly attached using AUX-2
# define BTN_EN1 37
# define BTN_EN2 35
2016-01-15 20:42:10 +01:00
# define BTN_ENC 43
2015-10-16 11:04:50 +02:00
# define BLEN_C 2
# define BLEN_B 1
# define BLEN_A 0
# endif
# endif //ULTRA_LCD
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
/****************************************************************************************
* FELIXprinters
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 101
# define KNOWN_BOARD 1
//////////////////FIX THIS//////////////
# ifndef __AVR_ATmega1280__
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# endif
# define ORIG_X_STEP_PIN 54
# define ORIG_X_DIR_PIN 55
# define ORIG_X_ENABLE_PIN 38
# define ORIG_X_MIN_PIN 3
# define ORIG_X_MAX_PIN -1
# define ORIG_Y_STEP_PIN 60
# define ORIG_Y_DIR_PIN 61
# define ORIG_Y_ENABLE_PIN 56
# define ORIG_Y_MIN_PIN 14
# define ORIG_Y_MAX_PIN -1
# define ORIG_Z_STEP_PIN 46
# define ORIG_Z_DIR_PIN 48
# define ORIG_Z_ENABLE_PIN 62
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 26
# define ORIG_E0_DIR_PIN 28
# define ORIG_E0_ENABLE_PIN 24
# define ORIG_E1_STEP_PIN 36
# define ORIG_E1_DIR_PIN 34
# define ORIG_E1_ENABLE_PIN 30
# define LED_PIN 13
# define ORIG_FAN_PIN 9
# define ORIG_PS_ON_PIN 12
# define KILL_PIN -1
# define HEATER_0_PIN 10
2016-01-15 20:42:10 +01:00
//BED
# define HEATER_1_PIN 8
2015-10-16 11:04:50 +02:00
# define HEATER_2_PIN 7
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING
# define TEMP_0_PIN 13
// BED,ANALOG NUMBERING
# define TEMP_1_PIN 14
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN 15
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define SDPOWER 1
# define SDSS 53
# define ORIG_SDCARDDETECT 6
# define SDSUPPORT 1 // already defined in config.h
# define SDCARDDETECTINVERTED 1 // already defined in config.h
2016-07-02 18:11:43 +02:00
// these pins are defined in the SD library if building with SD support
2016-01-15 20:42:10 +01:00
// PINB.1, 20, SCK
2016-07-02 18:11:43 +02:00
# define SCK_PIN 52
2016-01-15 20:42:10 +01:00
// PINB.3, 22, MISO
2016-07-02 18:11:43 +02:00
# define MISO_PIN 50
2016-01-15 20:42:10 +01:00
// PINB.2, 21, MOSI
2016-07-02 18:11:43 +02:00
# define MOSI_PIN 51
2016-01-15 20:42:10 +01:00
//53 // PINB.0, 19, SS
# define MAX6675_SS -1
2015-10-16 11:04:50 +02:00
# define BEEPER_PIN -1 // Activate beeper on extension shield
# define BEEPER_TYPE 1
# endif //MOTHERBOARD == 101
/****************************************************************************************
* MegaTronics v2 .0
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 701
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 26
# define ORIG_X_DIR_PIN 27
# define ORIG_X_ENABLE_PIN 25
# define ORIG_X_MIN_PIN 37
2016-01-15 20:42:10 +01:00
//2 //Max endstops default to disabled "-1", set to commented value to enable.
# define ORIG_X_MAX_PIN 40
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Y_STEP_PIN 4
# define ORIG_Y_DIR_PIN 54
2015-10-16 11:04:50 +02:00
# define ORIG_Y_ENABLE_PIN 5
# define ORIG_Y_MIN_PIN 41
2016-01-15 20:42:10 +01:00
# define ORIG_Y_MAX_PIN 38
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Z_STEP_PIN 56
# define ORIG_Z_DIR_PIN 60
# define ORIG_Z_ENABLE_PIN 55
2015-10-16 11:04:50 +02:00
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN 19
# define ORIG_E0_STEP_PIN 35
# define ORIG_E0_DIR_PIN 36
# define ORIG_E0_ENABLE_PIN 34
# define ORIG_E1_STEP_PIN 29
# define ORIG_E1_DIR_PIN 39
# define ORIG_E1_ENABLE_PIN 28
# define ORIG_E2_STEP_PIN 23
# define ORIG_E2_DIR_PIN 24
# define ORIG_E2_ENABLE_PIN 22
# define ORIG_SDCARDDETECT -1 // Ramps does not use this port
# define SDPOWER -1
# define SDSS 53
# define LED_PIN 13
# define ORIG_FAN_PIN 7
# define ORIG_FAN2_PIN 6
# define ORIG_PS_ON_PIN 12
2016-01-15 20:42:10 +01:00
// EXTRUDER 1
# define HEATER_0_PIN 9
// Heated bed
# define HEATER_2_PIN 8
// EXTRUDER 2
# define HEATER_1_PIN 10
// Thermistor 0 ANALOG NUMBERING
# define TEMP_0_PIN 13
// Thermistor 1 ANALOG NUMBERING
# define TEMP_2_PIN 15
// Thermistor 2 for heated bed ANALOG NUMBERING
# define TEMP_1_PIN 14
// Thermocouple 0
# define TEMP_3_PIN 8
// Thermocouple 1
# define TEMP_4_PIN 4
2015-10-16 11:04:50 +02:00
# define THERMOCOUPLE_0_PIN 8
2016-07-02 18:11:43 +02:00
# define THERMOCOUPLE_1_PIN 4
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// Beeper on AUX-4
# define BEEPER_PIN 64
2015-10-16 11:04:50 +02:00
# define LCD_PINS_RS 14
# define LCD_PINS_ENABLE 15
# define LCD_PINS_D4 30
# define LCD_PINS_D5 31
# define LCD_PINS_D6 32
# define LCD_PINS_D7 33
//buttons are directly attached using AUX-2
# define BTN_EN1 59
# define BTN_EN2 64
2016-01-15 20:42:10 +01:00
# define BTN_ENC 43
2015-10-16 11:04:50 +02:00
# define BLEN_C 2
# define BLEN_B 1
# define BLEN_A 0
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# endif
/****************************************************************************************
* Minitronics v1 .0
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 702
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega1281__
# error Oops! Make sure you have 'Minitronics ' selected from the 'Tools -> Boards' menu.
# endif
# define LARGE_FLASH true
# define ORIG_X_STEP_PIN 48
# define ORIG_X_DIR_PIN 47
# define ORIG_X_ENABLE_PIN 49
# define ORIG_X_MIN_PIN 5
2016-01-15 20:42:10 +01:00
//2 //Max endstops default to disabled "-1", set to commented value to enable.
# define ORIG_X_MAX_PIN -1
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Y_STEP_PIN 39
# define ORIG_Y_DIR_PIN 40
2015-10-16 11:04:50 +02:00
# define ORIG_Y_ENABLE_PIN 38
# define ORIG_Y_MIN_PIN 2
2016-01-15 20:42:10 +01:00
# define ORIG_Y_MAX_PIN -1
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Z_STEP_PIN 42
# define ORIG_Z_DIR_PIN 43
# define ORIG_Z_ENABLE_PIN 41
2015-10-16 11:04:50 +02:00
# define ORIG_Z_MIN_PIN 6
# define ORIG_Z_MAX_PIN -1
# define ORIG_E0_STEP_PIN 45
# define ORIG_E0_DIR_PIN 44
# define ORIG_E0_ENABLE_PIN 27
# define ORIG_E1_STEP_PIN 36
# define ORIG_E1_DIR_PIN 35
# define ORIG_E1_ENABLE_PIN 37
# define ORIG_E2_STEP_PIN -1
# define ORIG_E2_DIR_PIN -1
# define ORIG_E2_ENABLE_PIN -1
# define SDPOWER -1
# define SDSS 16
# define SCK_PIN 10
# define MISO_PIN 12
# define MOSI_PIN 11
# define LED_PIN 46
# define ORIG_FAN_PIN 9
# define ORIG_FAN2_PIN -1
# define ORIG_PS_ON_PIN -1
# define KILL_PIN -1
2016-01-15 20:42:10 +01:00
// EXTRUDER 1
# define HEATER_0_PIN 7
// BED
# define HEATER_1_PIN 3
// EXTRUDER 2
# define HEATER_2_PIN 8
2015-10-16 11:04:50 +02:00
# define HEATER_3_PIN -1
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING
# define TEMP_0_PIN 7
// BED SENSOR ANALOG NUMBERING
# define TEMP_1_PIN 6
// ANALOG NUMBERING
# define TEMP_2_PIN 6
// ANALOG NUMBERING
# define TEMP_3_PIN -1
2015-10-16 11:04:50 +02:00
# define BEEPER_PIN -1
# define ORIG_SDCARDDETECT -1 // Megatronics does not use this port
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS
# endif
/****************************************************************************************
* MegaTronics v3 .0
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 703
# define KNOWN_BOARD 1
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 58
# define ORIG_X_DIR_PIN 57
# define ORIG_X_ENABLE_PIN 59
# define ORIG_X_MIN_PIN 37
2016-01-15 20:42:10 +01:00
//2 //Max endstops default to disabled "-1", set to commented value to enable.
# define ORIG_X_MAX_PIN 40
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Y_STEP_PIN 5
# define ORIG_Y_DIR_PIN 17
2015-10-16 11:04:50 +02:00
# define ORIG_Y_ENABLE_PIN 4
# define ORIG_Y_MIN_PIN 41
2016-01-15 20:42:10 +01:00
# define ORIG_Y_MAX_PIN 38
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# define ORIG_Z_STEP_PIN 16
# define ORIG_Z_DIR_PIN 11
# define ORIG_Z_ENABLE_PIN 3
2015-10-16 11:04:50 +02:00
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN 19
# define ORIG_E0_STEP_PIN 28
# define ORIG_E0_DIR_PIN 27
# define ORIG_E0_ENABLE_PIN 29
# define ORIG_E1_STEP_PIN 25
# define ORIG_E1_DIR_PIN 24
# define ORIG_E1_ENABLE_PIN 26
# define ORIG_E2_STEP_PIN 22
# define ORIG_E2_DIR_PIN 60
# define ORIG_E2_ENABLE_PIN 23
# define ORIG_SDCARDDETECT -1 // Ramps does not use this port
# define SDPOWER -1
# define SDSS 53
# define LED_PIN 13
# define ORIG_FAN_PIN 6
# define ORIG_FAN2_PIN 7
# define ORIG_PS_ON_PIN 12
//#define KILL_PIN -1
2016-01-15 20:42:10 +01:00
// EXTRUDER 0 - changed 10-9-2015
# define HEATER_0_PIN 2
// EXTRUDER 1 - changed 10-9-2015
# define HEATER_2_PIN 9
// EXTRUDER 2 - changed 10-9-2015
# define HEATER_3_PIN 8
// heater bed
# define HEATER_1_PIN 10
2015-10-16 11:04:50 +02:00
/*
Temperature sensors
ANALOG NUMBERING !
Thermistors
T0 = 15
T1 = 14
T2 = 13
T3 = 12
Thermocouple
S0 = 11
S1 = 10
S2 ( ext ) = 8
S3 ( ext ) = 9
*/
2016-07-02 18:11:43 +02:00
// Extruder 1 - Thermistor 1
# define TEMP_0_PIN 15
// Extruder 2 - Thermistor 2
# define TEMP_2_PIN 14
// Extruder 3 - Thermistor 3
# define TEMP_3_PIN 13
// Heated bed - Thermistor 4
# define TEMP_1_PIN 12
2015-10-16 11:04:50 +02:00
# define THERMOCOUPLE_0_PIN 11
# define THERMOCOUPLE_1_PIN 10
# define THERMOCOUPLE_2_PIN 8
# define THERMOCOUPLE_3_PIN 9
2016-01-15 20:42:10 +01:00
// Beeper on AUX-4
# define BEEPER_PIN 61
# define SDSUPPORT 1 // sd card reader on board
2015-10-16 11:04:50 +02:00
// #define UI_DISPLAY_RS_PIN 32
// #define UI_DISPLAY_ENABLE_PIN 31
// #define UI_DISPLAY_D4_PIN 14
// #define UI_DISPLAY_D5_PIN 30
// #define UI_DISPLAY_D6_PIN 39
// #define UI_DISPLAY_D7_PIN 15
//buttons are directly attached using AUX-2
////encoder A 59
////encoder B 64
////encoder click 33 //the click
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# endif
# if MOTHERBOARD == 301
# define KNOWN_BOARD
/*****************************************************************
* RAMBo Pin Assignments
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
# endif
# define ORIG_X_STEP_PIN 37
# define ORIG_X_DIR_PIN 48
# define ORIG_X_MIN_PIN 12
# define ORIG_X_MAX_PIN 24
# define ORIG_X_ENABLE_PIN 29
# define X_MS1_PIN 40
# define X_MS2_PIN 41
# define ORIG_Y_STEP_PIN 36
# define ORIG_Y_DIR_PIN 49
# define ORIG_Y_MIN_PIN 11
# define ORIG_Y_MAX_PIN 23
# define ORIG_Y_ENABLE_PIN 28
# define Y_MS1_PIN 69
# define Y_MS2_PIN 39
# define ORIG_Z_STEP_PIN 35
# define ORIG_Z_DIR_PIN 47
# define ORIG_Z_MIN_PIN 10
# define ORIG_Z_MAX_PIN 30
# define ORIG_Z_ENABLE_PIN 27
# define Z_MS1_PIN 68
# define Z_MS2_PIN 67
# define HEATER_0_PIN 9
# define TEMP_0_PIN 0
# define HEATER_1_PIN 3
2016-01-15 20:42:10 +01:00
// This is T2 on the board!
2015-10-16 11:04:50 +02:00
# define TEMP_1_PIN 2
# define HEATER_2_PIN 7
2016-01-15 20:42:10 +01:00
// This is T1 on the board!
2015-10-16 11:04:50 +02:00
# define TEMP_2_PIN 1
2016-01-15 20:42:10 +01:00
// T3 on board
2015-10-16 11:04:50 +02:00
# define TEMP_3_PIN 7
# define ORIG_E0_STEP_PIN 34
# define ORIG_E0_DIR_PIN 43
# define ORIG_E0_ENABLE_PIN 26
# define E0_MS1_PIN 65
# define E0_MS2_PIN 66
# define ORIG_E1_STEP_PIN 33
# define ORIG_E1_DIR_PIN 42
# define ORIG_E1_ENABLE_PIN 25
# define E1_MS1_PIN 63
# define E1_MS2_PIN 64
# define DIGIPOTSS_PIN 38
# define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping
# define SDPOWER -1
# define SDSS 53
# define LED_PIN 13
# define ORIG_FAN_PIN 8
# define ORIG_FAN2_PIN 6
# define ORIG_FAN3_PIN 2
# define ORIG_PS_ON_PIN 4
# define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing.
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,E0_MS1_PIN,E0_MS2_PIN,
# define E1_PINS
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define MAX6675_SS 53
# define STEPPER_CURRENT_CONTROL CURRENT_CONTROL_DIGIPOT
# endif
/***************************************************************************************
* PiBot for Repetier pins assignment
* illustration :
* PiBot for Repetier V1 .0 - 1.3 = 314
* PiBot for Repetier V1 .4 - 1.6 = 315
* PiBot Controller Rev2 .0 = 316
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 316
# define MOTHERBOARD 314
# define PiBot_V_2_0 true
# define PiBot_HD_VERSION "Rev2.0"
# ifndef Thermistor_Solution
# define Thermistor_Solution 0
# endif
2016-01-15 20:42:10 +01:00
// define for temperature senser chip connection
// temperature sensor port in Rev 2.0 for max6675
2015-10-16 11:04:50 +02:00
// #define MAX6675_TEMP_Senser false ///*** canceled hardware integration
2016-01-15 20:42:10 +01:00
// Temperature sensor port in Rev 2.0 for AD595
2015-10-16 11:04:50 +02:00
# define AD595_TEMP_Senser false /////*** you can input at port 59 60 61 ///Analoge Pin 8 9 10
# endif
# if MOTHERBOARD == 315
# define MOTHERBOARD 314
# define PiBot_V_1_6 true
# define PiBot_HD_VERSION "Rev1.6"
# endif
# if MOTHERBOARD == 314
# define KNOWN_BOARD 1
# define PiBot true
2016-07-02 18:11:43 +02:00
2015-10-16 11:04:50 +02:00
# if PiBot_V_1_4==true || PiBot_V_1_6==true || PiBot_V_2_0==true
# define PiBot_V_1_0 false
# else
# define PiBot_V_1_0 true
# define PiBot_HD_VERSION "Rev1.0"
# endif
# ifndef PiBotSemitec
2016-01-15 20:42:10 +01:00
# define PiBotSemitec false // for semitec NTC 100K b=4230(test value) default b=4267
2015-10-16 11:04:50 +02:00
# endif
# ifndef PI_PRUSA_I3
# define PI_PRUSA_I3 false
# endif
# ifndef PiBotMachine
2016-01-15 20:42:10 +01:00
# define PiBotMachine false // if use for pibot 3D printer uncomment this line.
2015-10-16 11:04:50 +02:00
# endif
# if PI_PRUSA_I3==true
2016-01-15 20:42:10 +01:00
# define PiBotMachine true // if use for pibot 3D printer uncomment this line.
2015-10-16 11:04:50 +02:00
# endif
2016-01-15 20:42:10 +01:00
// define in AVR public files, when you finish the chip select.
2015-10-16 11:04:50 +02:00
# ifndef __AVR_ATmega1280__
# ifndef __AVR_ATmega2560__
# error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
# endif
# endif
# if PiBot_V_1_0
# define ORIG_X_STEP_PIN 54
# define ORIG_X_DIR_PIN 55
# define ORIG_X_ENABLE_PIN 38
# define ORIG_X_MIN_PIN 3
# define ORIG_X_MAX_PIN 2
# define ORIG_Y_STEP_PIN 60
# define ORIG_Y_DIR_PIN 61
# define ORIG_Y_ENABLE_PIN 56
# define ORIG_Y_MIN_PIN 14
# define ORIG_Y_MAX_PIN 15
# define ORIG_Z_STEP_PIN 46
# define ORIG_Z_DIR_PIN 48
# define ORIG_Z_ENABLE_PIN 62
# define ORIG_Z_MIN_PIN 18
# define ORIG_Z_MAX_PIN 19
# define ORIG_E0_STEP_PIN 26
# define ORIG_E0_DIR_PIN 28
# define ORIG_E0_ENABLE_PIN 24
# define ORIG_E1_STEP_PIN 36
# define ORIG_E1_DIR_PIN 34
# define ORIG_E1_ENABLE_PIN 30
# define SDPOWER -1
# define ORIG_SDCARDDETECT 49
# define LED_PIN 13
2016-01-15 20:42:10 +01:00
# define ORIG_FAN_PIN 7
2015-10-16 11:04:50 +02:00
# define ORIG_PS_ON_PIN 12
# define KILL_PIN -1
2016-01-15 20:42:10 +01:00
// Extuder1
# define HEATER_0_PIN 8
// Bed
# define HEATER_1_PIN 10
// Extuder2
# define HEATER_2_PIN 9
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 13
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 15
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 14
// ISP for TFcard
2015-10-16 11:04:50 +02:00
# define SDSS 53
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
2016-01-15 20:42:10 +01:00
# endif // end PiBot for Repetier V1.0
2015-10-16 11:04:50 +02:00
# if PiBot_V_1_4==true || PiBot_V_1_6==true
# define ORIG_X_STEP_PIN 4
# define ORIG_X_DIR_PIN 17
# define ORIG_X_ENABLE_PIN 16
# define ORIG_X_MIN_PIN 37
# define ORIG_X_MAX_PIN 34
# define ORIG_Y_STEP_PIN 56
# define ORIG_Y_DIR_PIN 55
# define ORIG_Y_ENABLE_PIN 54
# define ORIG_Y_MIN_PIN 36
# define ORIG_Y_MAX_PIN 33
# define ORIG_Z_STEP_PIN 59
# define ORIG_Z_DIR_PIN 58
# define ORIG_Z_ENABLE_PIN 57
# define ORIG_Z_MIN_PIN 35
# define ORIG_Z_MAX_PIN 32
# define ORIG_E0_STEP_PIN 24
# define ORIG_E0_DIR_PIN 23
# define ORIG_E0_ENABLE_PIN 22
# define ORIG_E1_STEP_PIN 27
# define ORIG_E1_DIR_PIN 26
# define ORIG_E1_ENABLE_PIN 25
//uncomment when use 3rd extruder
# define ORIG_E2_STEP_PIN 15
# define ORIG_E2_DIR_PIN 14
# define ORIG_E2_ENABLE_PIN 39
//uncomment when use 4th extruder
# define ORIG_E3_STEP_PIN 41
# define ORIG_E3_DIR_PIN 38
# define ORIG_E3_ENABLE_PIN 13
# define SDPOWER -1
# define ORIG_SDCARDDETECT 10
# define LED_PIN 30
2016-01-15 20:42:10 +01:00
# define ORIG_FAN_PIN 7
2015-10-16 11:04:50 +02:00
//uncomment when the 2nd fan used - works only without heated bed!
# define ORIG_FAN2_PIN 2
# define PS_ON_PIN 40
# define KILL_PIN -1
2016-01-15 20:42:10 +01:00
// Extuder1
# define HEATER_0_PIN 3
// Bed
# define HEATER_1_PIN 12
// Extuder2
# define HEATER_2_PIN 6
// Extuder3
# define HEATER_3_PIN 9
// Extuder4
# define HEATER_4_PIN 11
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 14
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 15
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 13
// ANALOG NUMBERING Extuder3
# define TEMP_3_PIN 12
// ANALOG NUMBERING Extuder4
# define TEMP_4_PIN 11
//PiBot use this pin as Z-Probing pin
# define PiBot_Z_PROBE_PIN 64
// ISP for TFcard
2015-10-16 11:04:50 +02:00
# define SDSS 53
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
# define E2_PINS ORIG_E2_STEP_PIN,ORIG_E2_DIR_PIN,ORIG_E2_ENABLE_PIN,
# define E3_PINS ORIG_E3_STEP_PIN,ORIG_E3_DIR_PIN,ORIG_E3_ENABLE_PIN,
2016-01-15 20:42:10 +01:00
# endif // end PiBot for Repetier V1.4 or V1.6
2015-10-16 11:04:50 +02:00
# if PiBot_V_2_0==true
# define ORIG_X_STEP_PIN 24
# define ORIG_X_DIR_PIN 23
# define ORIG_X_ENABLE_PIN 22
# define ORIG_X_MIN_PIN 62
# define ORIG_X_MAX_PIN 63
# define ORIG_Y_STEP_PIN 27
# define ORIG_Y_DIR_PIN 26
# define ORIG_Y_ENABLE_PIN 25
# define ORIG_Y_MIN_PIN 64
# define ORIG_Y_MAX_PIN 65
# define ORIG_Z_STEP_PIN 15
# define ORIG_Z_DIR_PIN 14
# define ORIG_Z_ENABLE_PIN 39
# define ORIG_Z_MIN_PIN 66
# define ORIG_Z_MAX_PIN 67
# define ORIG_E0_STEP_PIN 32
# define ORIG_E0_DIR_PIN 31
# define ORIG_E0_ENABLE_PIN 30
# define ORIG_E1_STEP_PIN 35
# define ORIG_E1_DIR_PIN 34
# define ORIG_E1_ENABLE_PIN 33
2016-01-15 20:42:10 +01:00
// =========================================
# define PiBot_Z_PROBE_PIN 68 // PiBot use this pin as Z-Probing pin
2015-10-16 11:04:50 +02:00
# define LED_PIN -1
2016-01-15 20:42:10 +01:00
// PWM6 fan1
# define ORIG_FAN_PIN 6
// PWM7 fan2
# define ORIG_FAN2_PIN 7
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
// have hardware in PiBot HDV2.0
# define ORIG_PS_ON_PIN 17
2015-10-16 11:04:50 +02:00
# define KILL_PIN -1
2016-01-15 20:42:10 +01:00
// PWM5 Extuder1
# define HEATER_0_PIN 5
// PWM4 Bed
# define HEATER_1_PIN 4
// PWM2 Extuder2
# define HEATER_2_PIN 2
// for Pibot PWM Extuder3
# define HEATER_3_PIN -1
// for Pibot PWM Extuder4
# define HEATER_4_PIN -1
# if Thermistor_Solution==0 // 000 0 2 4
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 2
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 0
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 4
# endif
# if Thermistor_Solution==1 // 001 1 2 4
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 2
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 1
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 4
# endif
# if Thermistor_Solution==2 // 010 0 3 4
# define TEMP_0_PIN 3
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 0
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 4
# endif
# if Thermistor_Solution==3 // 011 1 3 4
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 3
# define TEMP_1_PIN 1
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 4
# endif
# if Thermistor_Solution==4 // 100 0 2 5
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 2
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 0
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 5
# endif
# if Thermistor_Solution==5 // 101 1 2 5
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 2
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 1
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 5
# endif
# if Thermistor_Solution==6 // 110 0 3 5
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 3
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 0
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 5
# endif
# if Thermistor_Solution==7 // 111 1 3 5
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 3
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 1
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 5
2015-10-16 11:04:50 +02:00
# endif
# if !defined(TEMP_0_PIN) || !defined(TEMP_1_PIN) || !defined(TEMP_2_PIN) ||!defined(Thermistor_Solution)
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 2
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 0
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 4
2015-10-16 11:04:50 +02:00
# endif
2016-01-15 20:42:10 +01:00
// ad595 temp senser
2015-10-16 11:04:50 +02:00
# if AD595_TEMP_Senser==true
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 8
// ANALOG NUMBERING Bed
# define TEMP_1_PIN 9
// ANALOG NUMBERING Extuder2
# define TEMP_2_PIN 10
2015-10-16 11:04:50 +02:00
# endif
2016-01-15 20:42:10 +01:00
// max6675 ISP port temp->ISP-ENABLE
// these enable pins have been isolated by capacitor
2015-10-16 11:04:50 +02:00
/*#if MAX6675_TEMP_Senser==true
2016-01-15 20:42:10 +01:00
// ANALOG NUMBERING Extuder1
# define TEMP_0_PIN 14 // ANALOG NUMBERING Extuder1
# define TEMP_1_PIN 15 // ANALOG NUMBERING Bed
# define TEMP_2_PIN 13 // ANALOG NUMBERING Extuder2
2015-10-16 11:04:50 +02:00
//uncomment when 3 extruder used
2016-01-15 20:42:10 +01:00
# define TEMP_3_PIN 12 // ANALOG NUMBERING Extuder3
2015-10-16 11:04:50 +02:00
# endif* /
2016-01-15 20:42:10 +01:00
// ISP for TFcard
2015-10-16 11:04:50 +02:00
# define SDPOWER -1
# define ORIG_SDCARDDETECT 40
# define SDSS 53
# define SCK_PIN 52
# define MISO_PIN 50
# define MOSI_PIN 51
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS ORIG_E1_STEP_PIN,ORIG_E1_DIR_PIN,ORIG_E1_ENABLE_PIN,
2016-01-15 20:42:10 +01:00
# endif // end PiBot Controller Rev 2.0
2015-10-16 11:04:50 +02:00
2016-01-15 20:42:10 +01:00
# endif // end PiBot for Repetier
2015-10-16 11:04:50 +02:00
/****************************************************************************************
* Sanguish Beta pin assignment
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# if MOTHERBOARD == 501
# define KNOWN_BOARD
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Your MCU / Bootloader' selected from the 'Tools -> Boards' menu.
# endif
//x axis pins
# define ORIG_X_STEP_PIN 28
# define ORIG_X_DIR_PIN 27
# define ORIG_X_ENABLE_PIN 29
# define ORIG_X_MIN_PIN 2
# define ORIG_X_MAX_PIN -1
//y axis pins
# define ORIG_Y_STEP_PIN 25
# define ORIG_Y_DIR_PIN 24
# define ORIG_Y_ENABLE_PIN 26
# define ORIG_Y_MIN_PIN 5
# define ORIG_Y_MAX_PIN -1
//z axis pins
# define ORIG_Z_STEP_PIN 22
# define ORIG_Z_DIR_PIN 21
# define ORIG_Z_ENABLE_PIN 23
# define ORIG_Z_MIN_PIN 1
# define ORIG_Z_MAX_PIN -1
//extruder pins
# define ORIG_E0_STEP_PIN 19
# define ORIG_E0_DIR_PIN 18
# define ORIG_E0_ENABLE_PIN 20
# define TEMP_0_PIN 1
# define TEMP_1_PIN 0
# define HEATER_0_PIN 3
# define HEATER_1_PIN 4
# define SDPOWER -1
# define SDSS -1
# define LED_PIN -1
# define ORIG_FAN_PIN -1
# define ORIG_PS_ON_PIN 0
//our pin for debugging.
# define DEBUG_PIN -1
//our RS485 pins
# define TX_ENABLE_PIN 12
# define RX_ENABLE_PIN 13
# define SDPOWER -1
# define SDSS -1
# define SCK_PIN 7
# define MISO_PIN 6
# define MOSI_PIN 5
# define E0_PINS ORIG_E0_STEP_PIN,ORIG_E0_DIR_PIN,ORIG_E0_ENABLE_PIN,
# define E1_PINS
# endif
# if MOTHERBOARD == 999
# define KNOWN_BOARD
# include "userpins.h"
# endif
# ifndef CPU_ARCH // Set default architecture
# define CPU_ARCH ARCH_AVR
# endif
# ifndef SDSSORIG
# define SDSSORIG -1
# endif
# ifndef STEPPER_CURRENT_CONTROL // Set default stepper current control if not set yet.
# define STEPPER_CURRENT_CONTROL CURRENT_CONTROL_MANUAL
# endif
# ifndef FAN_BOARD_PIN
# define FAN_BOARD_PIN -1
# endif
2016-07-02 18:11:43 +02:00
# ifndef E2_PINS
# define E2_PINS
# endif
2015-10-16 11:04:50 +02:00
# if NUM_EXTRUDER==1
# undef E1_PINS
# define E1_PINS
# endif
2016-01-15 20:42:10 +01:00
# if NUM_EXTRUDER < 3
2015-10-16 11:04:50 +02:00
# undef E2_PINS
# define E2_PINS
# endif
# ifndef HEATER_PINS_INVERTED
# define HEATER_PINS_INVERTED 0
# endif
// Original pin assignmats to be used in configuration tool
# define X_STEP_PIN ORIG_X_STEP_PIN
# define X_DIR_PIN ORIG_X_DIR_PIN
# define X_ENABLE_PIN ORIG_X_ENABLE_PIN
# define X_MIN_PIN ORIG_X_MIN_PIN
# define X_MAX_PIN ORIG_X_MAX_PIN
# define Y_STEP_PIN ORIG_Y_STEP_PIN
# define Y_DIR_PIN ORIG_Y_DIR_PIN
# define Y_ENABLE_PIN ORIG_Y_ENABLE_PIN
# define Y_MIN_PIN ORIG_Y_MIN_PIN
# define Y_MAX_PIN ORIG_Y_MAX_PIN
# define Z_STEP_PIN ORIG_Z_STEP_PIN
# define Z_DIR_PIN ORIG_Z_DIR_PIN
# define Z_ENABLE_PIN ORIG_Z_ENABLE_PIN
# define Z_MIN_PIN ORIG_Z_MIN_PIN
# define Z_MAX_PIN ORIG_Z_MAX_PIN
# define E0_STEP_PIN ORIG_E0_STEP_PIN
# define E0_DIR_PIN ORIG_E0_DIR_PIN
# define E0_ENABLE_PIN ORIG_E0_ENABLE_PIN
# define E1_STEP_PIN ORIG_E1_STEP_PIN
# define E1_DIR_PIN ORIG_E1_DIR_PIN
# define E1_ENABLE_PIN ORIG_E1_ENABLE_PIN
# define E2_STEP_PIN ORIG_E2_STEP_PIN
# define E2_DIR_PIN ORIG_E2_DIR_PIN
# define E2_ENABLE_PIN ORIG_E2_ENABLE_PIN
# define E3_STEP_PIN ORIG_E3_STEP_PIN
# define E3_DIR_PIN ORIG_E3_DIR_PIN
# define E3_ENABLE_PIN ORIG_E3_ENABLE_PIN
# define E4_STEP_PIN ORIG_E4_STEP_PIN
# define E4_DIR_PIN ORIG_E4_DIR_PIN
# define E4_ENABLE_PIN ORIG_E4_ENABLE_PIN
# define E5_STEP_PIN ORIG_E5_STEP_PIN
# define E5_DIR_PIN ORIG_E5_DIR_PIN
# define E5_ENABLE_PIN ORIG_E5_ENABLE_PIN
# define FAN_PIN ORIG_FAN_PIN
2016-01-15 20:42:10 +01:00
# ifdef ORIG_FAN2_PIN
2015-10-16 11:04:50 +02:00
# define FAN2_PIN ORIG_FAN2_PIN
2016-01-15 20:42:10 +01:00
# endif
2015-10-16 11:04:50 +02:00
# define PS_ON_PIN ORIG_PS_ON_PIN
# ifndef ORIG_SDCARDDETECT
# define ORIG_SDCARDDETECT -1
# endif
# define SDCARDDETECT ORIG_SDCARDDETECT
# define SENSITIVE_PINS {0, 1, ORIG_X_STEP_PIN, ORIG_X_DIR_PIN, ORIG_X_ENABLE_PIN, ORIG_X_MIN_PIN, ORIG_X_MAX_PIN, \
ORIG_Y_STEP_PIN , ORIG_Y_DIR_PIN , ORIG_Y_ENABLE_PIN , ORIG_Y_MIN_PIN , ORIG_Y_MAX_PIN , ORIG_Z_STEP_PIN , \
ORIG_Z_DIR_PIN , ORIG_Z_ENABLE_PIN , ORIG_Z_MIN_PIN , ORIG_Z_MAX_PIN , LED_PIN , ORIG_PS_ON_PIN , \
HEATER_0_PIN , HEATER_1_PIN , /*ORIG_FAN_PIN,*/ E0_PINS E1_PINS E2_PINS TEMP_0_PIN , TEMP_1_PIN , SDSS }
# endif
